Water Based Urethane Matte

$55.00$299.00

  • Matte finish
  • UV and yellow resistant
  • Durable against abrasions, chemicals, and hot tires
  • Low VOC and low odor
Save when you buy more!
Quantity Discount Per Item Price
4+ 4% $52.80
Savings shown in cart!
Save when you buy more!
Quantity Discount Per Item Price
4+ 4% $171.84
Savings shown in cart!
Save when you buy more!
Quantity Discount Per Item Price
4+ 4% $287.04
Savings shown in cart!
Clear
This product is estimated to be delivered in - business days after it ships. (Typically ships in 1 business day)

Product Description

Want a topcoat that can take a beating? A favorite for those with high traffic locations that want to keep the gloss low and can take high wear situations. This matte finish is a high solid, two-component water-based aliphatic polyurethane. Additionally, the water based finish features a design with high performance in mind. That is why this urethane finish has excellent hardness, as well as, abrasion, hot tire, and chemical resistance. On top of that, this product has low VOC and a low odor. Finally, the product offers multiple uses, thus allowing customers more freedom to work.

Advantages to this Water Based Urethane Finish:

  • Excellent abrasion and wear
  • UV resistance
  • Won’t turn yellow over time
  • Hot tire resistance to improve lifespan
  • Less odor for a friendlier application process
Pot Life 45-60 Minutes
Recoat or topcoats 16-24 Hours
Light Foot Traffic 24-48 Hours
Full Cure; Heavy Traffic 4-7 Days

SURFACE PREPARATION: The concrete surface must be deemed mechanically and structurally sound, thoroughly clean of debris and completely dry. Concrete must
be fully cured a minimum of 28 days. It is recommended to prepare the concrete surface by mechanical means such as shot blasting or diamond grinding with 30 grit or
coarser diamonds to achieve a CSP-2 to CSP-3 profile. If using in a thin mil system such as acid stain, dye & seal, 2 or less clear coats, etc., an 80 grit diamond, or a 30 or
50 Grit Satellite pad may be acceptable to minimizes visual scratches in the finish. Vacuum concrete surface several times until dust thoroughly removed, dry microfiber
wipe and ensure surface is free from dust.. If applying over an existing, fully bonded coating that is outside its recommended recoat window, the surface should be sanded
thoroughly with a 60-120 grit sanding screen until the surface is completely dulled with scratches. Vacuum dust thoroughly, rinse with clean water and remove excess
water with a wet/dry vacuum or floor scrubber. Allow surface to dry completely prior to application of coating. Where applicable and with adequate ventilation, wipe the
surface with acetone and a microfiber dust mop. CAUTION: Acetone is extremely flammable! If using acetone follow all safety precautions, make sure no pilot lights, open
flames, sources of static electricity, sparks or extreme heat sources are present. Use recommended personal protection for acetone.
Substrate, air and material temperatures must be no less than 50°F and not exceed 80°F. If applied outside these limits the coating may not achieve adequate film
formation and may have excessive air entrapment, bubbles, blushing or hazing. Please note that higher substrate, air and material temperatures as well as excessive
humidity may speed the cure rate of this product. Cooler temperatures and lower humidity may slow the cure rate of this product.
FOR PERSONAL PROTECTION USE GLOVES, GOGGLES, RESPIRATOR AND OTHER NECESSARY PPE. REFER TO SDS PRIOR TO USE!
TINTING: Suggested as a clear top coat only. Tinting is not recommended, but if needed can be tinted with WB Color Pack. Color float and/or inconsistent color profile
may leave an undesirable finish.

MIXING: If mixing less than a full kit, mix Part A and Part B separately with a stir stick, low speed mixer or vigorously shake containers prior to measuring out the smaller
kit to ensure uniform distribution of all ingredients. In a clean mixing container, blend 2 Parts A and 1 Part B using a drill mixer for 2-3 minutes. Up to 10% clean water may
be added AFTER blending Parts A and B to help reduce roller marks, orange peel, etc. Avoid creating a vortex in the material which could introduce air and/or moisture
content to the mixture. Do not mix more than can be applied within the usable pot life time frame.

APPLICATION: Using a brush and/or 3/8” nap shedless roller, dip and roll the mixed material from a roller pan. 18” rollers are recommended for any surface to speed
up application time and reduce roller marks. Start by placing the wet roller at one corner of an approximate 4’ x 4‘ square and roll the material at an angle to opposite
corner applying no pressure to the roller. Spread the material across only that square and immediately back-roll to even out material and roller lines. Adjust the size of
your square as needed based on the amount of material being applied with the roller. After finishing the square, move on to the next square using the same technique.
While applying keep a wet edge to prevent roller marks. It is recommended to work in sections usually using control joints as dividers to ensure proper application results.
Apply the mixed material within the usable pot life time frame. If the material becomes thick while applying and sticking to the roller, stop applying and discard the mixed
material. At this point it has reached the end of the usable pot life. Do not allow to puddle! Use a brush to remove excess coating in joints. An airless or HVLP sprayer may
also be used.

RECOATING: If possible, recoat within the suggested recoat window. Apply additional coats in the same manner as the first coat. Note that higher
substrate, air and material temperatures as well as excessive humidity may greatly reduce the acceptable recoat window of this product. When working in higher
temperatures, always recoat as early in the recoat window as possible to avoid failure between coats. If recoating outside the suggested recoat window (see page 1) or
beyond 24 hours, sand using a 120-220 grit sanding screen to ensure adequate adhesion between coats. Vacuum dust thoroughly, rinse with clean water and remove excess
water with a wet/dry vacuum or floor scrubber. Allow surface to dry completely prior to application of coating. Where applicable and with adequate ventilation, wipe the
surface with acetone and a microfiber dust mop. CAUTION: Acetone is extremely flammable! If using acetone follow all safety precautions, make sure no pilot lights, open
flames, sources of static electricity, sparks or extreme heat sources are present. Use recommended personal protection for acetone.

Data Sheets
Container Size 1.5 Gallons, 3 Gallon Kits
Coverage Rates 175 – 350 square feet per gallon depending on concrete porosity, prep and application style.
VOCs < <100 grams per liter
Shelf Life Up to one year from manufacture date in its original, unopened container stored at room temperature.
Appearance – Wet Clear
Appearance – Dry Clear, Matte
YouTube player

Related Products