Shop

Sale

U Epoxy It ™ | Epoxy Flow 100

$40.00$748.00

Clear
SKU: N/A Categories: ,
Description

Epoxy Flow 100 is our #1 selling coating material. It is a 100 percent solids clear epoxy that can be used for a variety of purposes. This product can be tinted with pigment for solid color floors, mixed with metallic pigments, used as a broadcast coat, or used for a topcoat.

Epoxy Flow 100 is very easy to apply, and has great flow characteristics. This is a professional grade epoxy coating.

It is sold in 3 Pint, .75 Gallon, 3 Gallon and 15 Gallon kits with a 2/1 blended ratio.

Please note: coverage rates vary depending on customer preference, prep and application techniques. Concrete Floor Supply and Super Z LLC do not guarantee precise coverage rates for this product. For more information on how to use the epoxy system please visit here.

Dry Times
Pot Life 20-30 Minutes
Tack Free; Dry to the touch 6-8 Hours
Recoat or topcoats 10-16 Hours
Light Foot Traffic 14-18 Hours
Full Cure; Heavy Traffic 2-7 Hours
Data
Data Sheets
SDS Part A
SDS Part B
Container Size 3 pint, .75 Gallons, 3 Gallon and 15 Gallon Kits
Metallic Coverage Rates 80-100 square feet per gallon
Epoxy Flake and Color Coverage Rates 100-125 square feet per gallon
VOCs Less than 5 grams/Liter
Recommended Film Thickness 16-18 mils
Shelf Life Up to one year from manufacture date in its original, unopened container stored at room temperature.
Appearance – Wet Clear; may show a slight haze while drying.
Appearance – Dry Clean and High Gloss
Instructions

SURFACE PREPARATION: A fine to medium shot blasting or the use of a diamond grinding machine to obtain a surface profile of a CSP – 3 to a CSP – 5 is suggested for ultimate adhesion. A test should be made to determine that the concrete is dry; this can be done by placing a 4 x 4 plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate should be ready to coat. More advanced moisture testing kits should be used on floors with suspected moisture problems. Epoxy Flow 100 is designed to be applied only to primed surfaces within the recommended recoat window of the primer or previously sealed surfaces that have sufficient adhesion to the substrate. Apply coating to a clean surface that is completely dry and free of oil, dirt, grime, wax, detergent or any incompatible paint or coating. If applying to an existing fully cured and fully adhered coating, the surface must be cleaned and sanded with 80—100 grit sandpaper. If multiple coats of Epoxy Flow 100 are required apply the second coat as close as possible to the suggested recoat time (see technical information section on this data sheet). Do not exceed 24 hours to recoat or a light sanding may be needed for adequate adhesion between coats.

PRIMING: We always suggest priming your concrete with a moisture mitigation primer M.V.B. This gives your extra protection from moisture that could possibly come up through your concrete and gives you better adhesion.

PRODUCT MIXING: Pour a full pre-packaged kit of 2 parts of Part A to 1 part of Part B together and mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed. Avoid whipping air into the coating. Improper mixing may result in product failure.

PRODUCT APPLICATION: Apply the mixed material with a brush, roller, trowel, notched squeegee or gauge rake and then back roll evenly to maintain the desired thickness within the usable pot life time frame, as well as the recommended temperature and relative humidity guidelines listed in the Technical Information section. If concrete conditions or aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating. If the material becomes thick while applying and sticking to the application tools, stop applying and discard the mixed material. At this point it has reached the end of the usable pot life. While applying keep a wet edge to prevent streaking. It is recommended to work in sections usually using control joints as dividers to ensure proper application results. Do not allow to Puddle! If recoating after 24 hours a light sanding using a fine sanding screen may be needed to ensure adequate inner coat adhesion.

Additional Information

Additional Information

Weight N/A
Product Reviews

Reviews

There are no reviews yet.

Be the first to review “U Epoxy It ™ | Epoxy Flow 100”

Your email address will not be published. Required fields are marked *